christof139
Posts: 980
Joined: 12/7/2006 Status: offline
|
quote:
don't like the 3D combat in FoF for the following reasons: it's way too slow and 'klunkly, and takes WAY TOO MUCH TIME!!! Chris To reply to my own quote listed above: I got rid of some of the klunkiness and/or slowness in HW (DC) by discovering that hooking-back-up my diconnected printer help smooth things out, as it being not connected befuddled and bogged down system resources even though I had closed the 'disconnected device icon' down. Ta-da. It's the simple things in life sometimes that do it for you. Also, I have 3 DIMM's of 1GB memory, ywo of one brand-make and 1 of another, and I made sure I had the two of one brand in slots next to each other. All three DIMM's have been tested by me with memory diagnostics and are good, and the BIOS and WinXP show that I have 3GB's of RAM, however FoF, EA BFME2, and my Creative Soundblaster Card diagnostics show only 2GB's. Wierd, but I have a 2002 Acer AX45-V Mobo and one online diagnostc showed I had 3GB's of RAM and 4-RAM Slots, when I have only 3-RAM slots. Therefore, my memory is good now and properly working and it helps a lot. I did have a bad ACP-Add-on 1GB DIMM but they replaced it quickly w/o any problems as it had a lifetime warranty. BFME2 and RotWK run good with some settings on ultra high and high, some on low, and some on medium. FoF runs very quickly now with music and sound and all. The smoke in HW still slows things a bit, not much, and I intend to shut-off the smoke as I did before, and maybe also the 'jiggling'-wiggling of the little unit sprites. Too much stuff like that slows even fast compooter, ties up RAM memory usage, adds to data processing bottlenecks, etc. which all adds-up to speed loss and slowness and bogging down of the system. I only have a PNY GeForce FX5200 256MB 8xAGP card running at 4xAGP, and it works very well. My old Acer Mobo won't support anything above 4xAGP, but it will support 4xAGP and lower, which is nice so then you can buy cheap older video cards to use like I did. The 478 pin 2.5GHz P4 late stepping (latter production with minor improvements usually) Northwood Core CPU I have overclocked to 2.8 to about 3.1GHz (believe it or not the processing speed can vary) with only a 112 x 4 = 448FSB instead of the stock 100 x 4 = 400FSB, and it runs nice and cool with stock factory cooling fan and heatsink, and it is fast. EA's BFME2 identified this CPU as running at about 3.1GHz once, with Hyper Threading (and it does not have HT), so the EA diagnostics must sometimes identify Intel's Net burst Architecture as Intel's HT. These diagnostics also id this with a 2.0GHz Northwood I have, and it was overclocked to 2.2GHz or so. The diagnostics correctly identify CPU's with the factory set speed, and what you actually overclock their speed to, which is very nice to know, although this is also shown in WinXP and sometimes the BIOS. Northwoods were and are great CPU's. My new system will have 4GB's of 400, 533 or 667 MHz DDR2 RAM on an Intel Mobo that can support Dual Core (not Core Duo) P-D's, and any 775 Socket P4, so I am using a P4 571 3.8MHz with 1MB L2 buffer/cache memory and HT, and of course the Mobo also supports HT. So, this thing will smoke playing any strategy/historical game and running regular day to day prigrams. Chris
|