Adding units to EF II & WF. (Full Version)

All Forums >> [Current Games From Matrix.] >> [World War II] >> John Tiller's Campaign Series >> Mods and Scenarios



Message

Nebfer -> Adding units to EF II & WF. (12/18/2007 9:27:46 PM)

I was wondering what Im doing wrong with adding units to the game.

I dont have this version of the game only the older ones (i.e Pre matrix)

But I have figured out how to add units to east front and west front but every time I do it allways removes the Sturm panzer IV unit.

is there any thing I should know about adding units? (I found the Unit creator programe in the below link and have bee using that.)

http://www.matrixgames.com/forums/tm.asp?m=1478661



Jason Petho -> RE: Adding units to EF II & WF. (12/18/2007 9:32:23 PM)

Are you using the same platoon number as the Sturm Panzer IV? That would cause a conflict.

Jason Petho



Nebfer -> RE: Adding units to EF II & WF. (12/18/2007 9:57:30 PM)

I dont think so

This is the unit I want to add
P01230 6 7 8 35 50 25 10 5 0 2 0 0 0 0 0 5 74 P01215 5 2 131 0 3 5 44 6 45 5 0 0 0 Sturm Platoon , Strm Pltn ,

(note: this is a late war platoon equiped with STG-44s for reguler army units)

and this is the Sturm Panzer IV
P01025 4 3 9 50 0 0 40 20 28 2 4 1 9 0 1 30 16 P01025 6 33 16 1 8 13 43 7 45 5 16 4 4 StuPz IV 150mm Assault Guns , StuPz IV , Brummbär (Grizzly Bear)

whats intersting is that it shows up in the the weapon.pdx and platoon01.obx but dose not show up in the oob editer (infact I had to change the company01.oob file becuse it had a invalied unit -the Sturm panzer!)

I even tryed to create a new Sturm panzer to see if that would work (labled as P01098 in the OBX and PDX files) and that dose not work.


Could it be becuse Im using the orginal East Front II (and west front) and not the Matrixs version? and the unit creater program dose not work with this version?



Jason Petho -> RE: Adding units to EF II & WF. (12/18/2007 10:01:06 PM)

Not sure if you know, but you have to do you edits in the oob file, and then run that oob file in the encryption program. If you don't use the encryption, it won't work in the editor.

Edited Platoon file: platoon01.oob
In file: plato01.oob
Out file: plato01.obx
New Encrypted Platoon file: platoon01.obx

Jason Petho



Nebfer -> RE: Adding units to EF II & WF. (12/18/2007 10:04:58 PM)

Thats what iv'e done
Edit the unit in the oob file
run the file in the editer -
platoon1.oob
platoon1.obx
encrypt
eastfront II

and the same thing for the Weapons.pdt

then move the files into the base EF folder.



Jason Petho -> RE: Adding units to EF II & WF. (12/18/2007 10:16:13 PM)

Hmm. Not sure what else to suggest. Can you post the file here so I can look at it?

Jason Petho



Nebfer -> RE: Adding units to EF II & WF. (12/18/2007 10:18:15 PM)

the OBX files or the reguler files?

oh and how do I add files? -do I have to uploded them to something like fileshack? edit: never mind that bit I found the upload area.



Nebfer -> RE: Adding units to EF II & WF. (12/18/2007 11:35:27 PM)

ok here's the files -as the fourms dont seem to alow zip uploads just TXT files

heres the weapons.pdt



Nebfer -> RE: Adding units to EF II & WF. (12/18/2007 11:36:02 PM)

and here's the Platoon01.oob



Page: [1]

Valid CSS!




Forum Software © ASPPlayground.NET Advanced Edition 2.4.5 ANSI
6.984375